Page tree
Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 16 Next »

What does "Discovery" in Unimus mean?

To make device management easier and to automate bulk operations, Unimus uses a discovery mechanism. Thanks to discovery, you do NOT need to give Unimus precise information about every device in the system (such as username/password, vendor, device type, model, etc.). Unimus will be able to discover all of the details about your devices automatically. This heavily decreases workload when deploying Unimus to your network, as all Unimus needs are IP addresses of your devices, nothing else. In other words, you can import 100 devices into Unimus using our Address import feature, and they will all start working properly, instead of having to manually configure the details for each device.

What happens during Discovery?

The discovery mechanism works in stages:

Detect available connector

All available ports for all enabled connectors are checked.

Secure connectors are always preferred to insecure connectors.
For example, if a device is available over both Telnet and SSH, SSH will be used.

Detect credentials

Credential discovery works differently depending if the device is set to "Discover" credentials, or has "Bound" credentials.

If credential discovery enabled:
  All credentials configured in the 'Credentials' settings are checked against the device.
  Credentials are checked against the device in random order.

  Whichever credentials work on the device first will be used for any future operations with this device.

When credentials bound to device:
  Only bound credentials are tested against the device
  If bound credentials do not work, the job fails

Detect device vendor and model

After correct connector and credentials are known, Unimus discovers the device.

The Vendor, Type and Model of the device is discovered.

Detect available CLI modes on the device

After Unimus knows exactly which device it's working with, it discovers available CLI modes (enable / configure mode - for example "privileged exec" and "configure" on Cisco).

When is Discovery performed?

Device addition into the system

The discovery mechanism is what makes only the address of the device required when adding a new device into Unimus.
Unimus will automatically discovered everything else about the device.

Import

When 400 devices are imported into Unimus, Unimus will automatically discover all the necessary details about each of the devices, and start backing them up automatically.
If proper connectors and credentials are configured, no additional steps other than importing the devices are needed.

This saves time for the administrators, and automates the work-flow.

Scheduled backups

Unimus performs a discovery before each scheduled backup.
This is to make sure Unimus knows current information about the device (connector, credentials, vendor, model, etc.).

The discovery before backup is necessary to make sure Unimus doesn't user wrong commands on the device.
In certain situations (ex. when a device is changed for another device) it's possible commands to generate backups on some vendors can actually cause configuration changes for other vendors.
Due to this (and other edge-cases) Unimus does a discovery before every backup.

Credential changes

Discovery mechanism will also be used if any device operation fails.
For example, if credentials which were previously used on a device are no longer valid on that device, Unimus will re-run discovery.

This means that if credentials used on 400 devices need to be changed, the only change needed in Unimus is to reconfigure the credentials in 'Credentials' settings.
Discovery mechanism will take care of the rest.

Device hardware changes

Discovery will automatically be re-run when device hardware change is detected.
For example, when a Cisco device is replaced with a MikroTik, or a HP device with an UBNT device, Unimus will handle this automatically.

This means that if devices are changed around the network, Unimus will automatically adjust to the situation, without the need for user interaction.

How to find out why device didn't discover?

There are 2 places in Unimus where you can see why discovery failed.

  • Dashboard > Latest failed jobs
    You can select the discovery job, and press 'Show log'.

  • Logs
    '/var/log/unimus' or 'C:\ProgramData\Unimus\log'

If you can't identify why you device didn't discover properly from either of these, feel free to contact support.
We will always be happy to help with any issues.

  • No labels